Rotronic CO2 Display Bedienungsanleitung PDF herunterladen

CO2-DISPLAY 18.07.2013 11:39:41

ROTRONIC AG, CH-8303 Bassersdorf

Tel. +41 44 838 11 44, www.rotronic.com

ROTRONIC Messgeräte GmbH, D-76275 Ettlingen

Tel. +49 7243 383 250, www.rotronic.de

ROTRONIC SARL, 56, F - 77183 Croissy Beaubourg

Tél. +33 1 60 95 07 10, www.rotronic.fr

ROTRONIC Italia srl

, I- 20157 Milano

Tel. +39 2 39 00 71 90, www.rotronic.it

ROTRONIC Instruments (UK) Ltd, West Sussex RH10 9EE

Phone +44 1293 571000, www.rotronic.co.uk

ROTRONIC Instrument Corp, NY 11788, USA

Phone +1 631 427-3898, www.rotronic-usa.com

ROTRONIC South East Asia Pte Ltd, Singapore 339156

Phone +65 6294 6065, www.rotronic.com.sg

ROTRONIC Shanghai Rep. Ofﬁce, Shanghai 200233, China

Phone +86 40 08162018, www.rotronic.cn

CO2

Temperature

Real time clock

Humidity

REC

INSTRUCTION MANUAL

General description

This CO

2 panel is an accurate wall mount and desktop data logger that displays and

records relative humidity, temperature and CO

2. Date and time is additionally displayed.

Program m ing

Most of the settings, such as memory clear, CO

2 status indicator, units (°C/°F),

sampling rate, pressure compensation and real time clock can all be changed using

the function keys.

Function keys

Desktop stand

Display

Hum idity Calibration

This meter can be calibrated either via 35 % rH & via 80 % rH humidity standards.

The ambient condition is recommended as stable 25°C.

CAUTION:

Do not calibrate the humidity without the default humidity standards. Otherwise,

it will cause permanent damage. Contact Rotronic for humidity standards or

services.

Single point calibration will cause error code E11 or non accurate reading.

Always do dual point calibration to complete a process. Suggest starting calibration

from low humidity.

Congratulations on your purchase on the new wall mount humidity, temperature and

2 instrument. Please read these instructions carefully before installing the device.

Humidity/Temperature sensor cover

USB stick slot

Opening for a simple CO2 calibration

Power Supply

The CO

2 panel uses 12VDC power adapter, which is included in the package.

Meter Setup

Hold down “ SET” key for more than 2 seconds until entering setup mode. To exit

setup, press “ESC” to return to normal mode.

The available meter setup program are shown in below. Press “UP” or “DOWN”

key to select the program (P10, P20, P30, P40 or P50) in main menu and press “SET”

key to enter sub menu. Press “SET” key to select different sub menu (P11, P12, P13

or P14), programmable setting then flashes on panel. Press “UP” or “DOWN” key to

adjust and press “SET” to confirm. To leave without saving, press “ESC” key to return.

Technical Data

Trouble Shooting

Error Messag es Solution

Calibration via humidity standards

Power on the device, plug the sensor probe into 35% humidity standard. Press “SET”

+”START”+”DOWN” keys simultaneously for 3 seconds to enter calibration mode.

Press “UP” or “DOWN” key to select 350 (35.0% calibration) and press “SET” to start.

“Calibrating value” (35.2% if at 25°C) is blinking on the LCD.

Waiting for 60 minutes to complete the 35% calibration. To quickly save, press “SET”

key any time. 800 (80.0% calibration) comes right after 35% calibration is done. Within

20 minutes, press “SET” key to start 80.0% calibration. “calibrating value” are blinking

on the LCD. Waiting for 60 minutes to complete the 80% calibration. To quickly save,

press “SET” key any time.

Now, the device is well calibrated. To abort without saving, press “ESC” to quit

without saving.

E01 CO

2 sensor is out of order

E33 CO

2 sensor is out of order

E02 measured value is under range

E03 measured value is over range

E11 RH calibration error

E31 Temp. sensor or AD damaged

E32 Memory IC damaged

E33 RH sensor or circuit damaged

E60~E65 USB download error

Humidity/accuracy:

Temperature/accuracy:

2 /accuracy:

Storage and transit:

Operating limit at electronics:

Memory:

Dimension,mm:

Weight:

Power consumption:

DC power type:

PC connection:

0.1~99.9%/±3%(10~95%@25

C). ±5%(others)

0...50

C/±0.3

C@5~40

0...9999ppm/±(30ppm+5% of reading)@0~5000ppm

-20...60

C/10...90%rh, non condensing.

0...50

6000 records auto logging for each parameter.

330(L) x 250(W) x 50(H)

1400 g

Max. 0.7A

12VDC

USB stick

GOOD

NORMAL

POOR

REC

2 value is in “GOOD” range

2 value is in “NORMAL” range

2 value is in “POOR” range

Unit of relative humidity

Unit of temperature (Celsius/Fahrenheit)

Blinking in automatic logging mode

P 11 (CLr), Clear logging memory

Choose YES/NO

P 10 (Lo9) Logging related setup

P12 (End), Data record mode

Choose STOP/LOOP

P 20 (CO

2) CO2 related setup

P13 & P14 (rATE), Logging

sampling rate

Choose from 00:01 to 12:59

P 21 (Nor) lower limit of “NORMAL”

icon

P 22 (Poor) lower limit of “POOR”

icon

P 23 (AbC) ABC function on/off

P 30 (uniT) Temperature unit setup

P 31, choose

P 40 (PrES) Pressure compensation

P 50 (rTC) Real Time Clock setup

P 51 choose 12 or 24 hour format

Note:

-Factory preset at 12H

-Factory preset at 2013.01.01,

12:00

Note:

-Factory preset at 1013hpa

-The adjustable scale is every 1hpa

Note:

-Factory preset

Note:

-donE: displayed while memory is c

leared

USB stick connection

Recorded data can be easily downloaded to USB stick and save as *.XLS file. Easily

analyze the recorded data through the free software SW21 or through Excel.

Turn off meter and re-start again

Retry CO

2 calibration

Put meter in normal condition

Retry humidity calibration

Return for repair

Suggest to format USB stick or try a new type

of memory stick.

TAKING MEASUREMENT

The device starts measurement when power on and update readings every second.

The meter can automatically record readings of CO

2/TEMP./RH for long time

environment monitoring. The memory capacity is 6000 points for each parameter.

Users can set up sampling rate from 1 minute to 12 hours and 59 minutes. The factory

default rate is 1 minute.

First, setup the data record mode you need. Hold down “SET” key for 2 seconds until

entering meter setup mode. Press “UP” or “DOWN” key to select the program P 10

and press “SET” key twice to enter P12. In P12, select the data record mode as

"STOP" or "LOOP". Press "UP" or "DOWN" key to select and then press "SET" to confirm.

"STOP": The device stops logging while the memory space is full.

"LOOP": After the memory is full, it starts to overwrite the oldest data.

Second, setup the sampling rate. Once finishing the P12 and press “SET” key, it

enters P13. Press “UP” or “DOWN” key to adjust the sample rate from hour to minute

and press “SET” key to confirm. Press “ESC” key to return to normal mode.

After sampling rate setting and data record mode are completed, press “ START” key

for 2 seconds under normal mode to start logging. The “REC” LED turn into green and

flash on panel to indicate the logging is in process.

To terminate data logging, press “ ESC” key for 2 seconds and green LED light vanish.

Repeat above to start another run of logging. If the data record mode is programmed

as "STOP", "REC" LED turn into red color and flash while the logging memory space is full.

DATALOGGING

DAT E/TIME SET UP

When device is powered on, hold down “SET” key for 2 seconds until entering device

setup mode. Press “UP” or “DOWN” key to select the program (P 50, displayed in

right-middle panel) and press “SET” key to enter.

First, choose the time format as 24 hour or 12 hour by press “UP” or “DOWN” key and

then press “SET” key to confirm. Now, start to input the real time clock value from

year, month, day, hour to minute. Press “UP” or “DOWN” key to adjust and the press

“SET” key to confirm.

After the date and time are set, a clearance of the memory must be performed. Press

“UP” or “Down” key to select P 10 and press “SET” key to enter P11. Press “UP” or

“Down” key to choose “YES” to clear previous memories and press “SET” to confirm.

Then, press “ESC” key twice to return to normal mode.

UNIT SET UP

Hold down “SET” key for 2 seconds until entering meter setup mode. Press “UP” or

“DOWN” key to select the program P 30 and press “SET” key to enter.

Press “UP” or “DOWN” key to select

°F or °C and the press “SET” key to confirm.

Press “ESC” key to return to normal mode.

Operation

Once the 12VDC power adaptor is connected, the device will be automatically

powered on. At power on, it performs 30 seconds countdown for device warm up,

then enters normal mode with real time clock displayed.

To power off, unplug the power adaptor.

POWER ON/OFF

The meter features logged memory download function by using a USB stick instead of

connecting it with a computer.

Before download, press “ESC” key for 2 seconds to stop the logging. Plug USB stick

(max. 8GB memory) to USB slot on device left side, hold down “DOWN” for more than 2

seconds until seeing " USb” appears on panel and then “USb” starts flashing on panel

to indicate the downloading is in process. It will take minutes to fully download the

memory. The data downloading time depends on memory size and USB stick.

The download data is saved as *.XLS file in USB stick. Using free ROTRONIC software

SW21 or Excel to analyze the data.

Suggest formatting your USB stick as FAT32 before using. If error code E60 ~ E65

appears on panel, suggest trying another model of USB memory stick.

MEMORY DOWNLOAD

The meter features light bar indicator to have user easily recognize the indoor air

quality. (See “Meter Setup” section for setting Normal & Poor threshold).

2 CONDITION INDICATOR

CO2-DISPLAY

12 VDC adapter port

-Press to select unit or increases value in setup mode

DOWN / DONWLOAD

-Press to select unit or decreases value in setup

-Press longer to download data to USB stick

Functions Keys

START/ESC

-“START”, Press longer to start automatic logging mode (REC is blinking)

-“ESC”, Press longer to stop logging mode

-“ESC”, Exits setup and calibration mode

SET

-In normal mode, press longer to enter setup mode

-STOP: Stop while memory is full

-LOOP: Overrides oldest values when

memory is full

Note:

-Factory preset at 1 minute

-The format is Hour: Min

Note:

-Adjustable level is 400 to 1000ppm

Preset at 800ppm

-Adjustable level is 1000 to 1400ppm

Preset at 1400ppm

-ABC preset as ON

P41 (hPA) Choose from 700 to 1990 hpa

P 52~54 Input Year/Month/Day

P 55~56 Input Hour/Minute

Pull out the humidity probe from panel

Before calibration, pull out the humidity probe from cover in panel rear side.

2 C alibration

CAUTION:

Do not calibrate the meter in the air with unknown CO

2 concentration. Otherwise,

it will be wrongly calibrated and leads to inaccurate measurements.

The meter can be calibrated in fresh outdoor air (on sunny day) at 400 ppm CO2.

Besides the 400 ppm, the meter can also be calibrated at 0 ppm or any value under

990 ppm. The latest calibration point is treated as final and meter will ignore the

previous calibration data.

Before calibration, plug in the pipe of the ROTRONIC CO

2-Calibrator into the

2-sensor on panel rear side and turn the CO2-Calibrator on.

Press “SET” +”START”+”DOWN” keys simultaneously for 3 seconds to enter

calibration mode. Press “UP” or “DOWN” key to select 400 (400 ppm) or 0 (0 ppm)

2 calibration. 0 ppm function is only for 0ppm CO2 calibration. For other CO2 value,

please choose 400 ppm and press “SET” to enter. The default value is 400 ppm but

you can press “UP” or “DOWN” key to adjust the value from 5 to 990 ppm, it is 5 ppm

per step. Once choosing the calibration value, press SET to start and see “CAL” and

2 value blink on LCD.

Wait about 10 minutes until the blinking stops to indicate the calibration is completed.

To abort calibration without saving, press “ESC” at any time.

SE T

START

ESC

Attention:

the cleanness of the CO

2-Calibrator air is 20...25 ppm.

CO2-DISPLAY 1

Inhaltsverzeichnis

Seite 1 - CO2-DISPLAY

CO2-DISPLAY 18.07.2013 11:39:41ROTRONIC AG, CH-8303 BassersdorfTel. +41 44 838 11 44, www.rotronic.comROTRONIC Messgeräte GmbH, D-76275 EttlingenTel

Kommentare zu diesen Handbüchern

Keine Kommentare

Rotronic CO2 Display Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Werkzeug Rotronic CO2 Display herunter. ROTRONIC CO2 Display User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Rotronic CO2 Display